首页 > 论文 > 电光与控制 > 19卷 > 4期(pp:72-75)

A CCD Image Processing Based Automatic Measurement System for Diopter and Optical Parallax

A CCD Image Processing Based Automatic Measurement System for Diopter and Optical Parallax

  • 摘要
  • 论文信息
  • 参考文献
  • 被引情况
  • PDF全文
分享:

摘要

为了实现对视度和视差的客观检测,提高自动化检测程度,设计了一种基于CCD图像处理的视度和视差自动检测系统。对CCD视度和视差检测原理公式进行了推导,通过分析发现需要测量成像最清晰时CCD光敏面的位置。为此,构建了像面可调的CCD摄像系统和图像采集与处理系统,采用扫描求解图像像素灰度值梯度的方法,实现图像清晰度测量和边缘提取;同时利用视频图像清晰度峰值搜索法,通过控制电机带动CCD光敏面朝图像最大清晰位置运动,实现CCD摄像系统的自动对焦,并完成对成像最清晰时CCD光敏面位置的测量。最后通过对装备视度和视差实际检测,表明视度检测不确定度在0.15 D以内,视差不确定度在0.3分以内,与传统方法相比,检测结果客观准确,自动化程度得到了提高。

Abstract

In order to achieve objective measurement of diopter and optical parallax and improve the level of automation,an automatic measurement system for diopter and optical parallax was designed based on CCD image processing.The measurement formula was deduced and the analysis showed that the location of CCD sensor needed to be tested when the CCD imaging was the clearest.A CCD camera system whose image plane was adjustable,and an image acquisition and processing system were built up.It achieved the test of image clarity and edge detection with the solution of scanning gray value gradient of image pixel.Under the control of the system,the motor drove the CCD sensor to the biggest definition position,by search of the video image peak to achieve the CCD camera system automatic focusing.Finally,experimental tests on the equipment showed that the uncertainty of diopter was less than 0.15 D,and optical parallax less than 0.3 arcminutes.Compared with the traditional methods,the automation of the measurement introduced in this paper was greatly improved,and the results are more objective and accurate.

Newport宣传-MKS新实验室计划
补充资料

中图分类号:V271.4

DOI:基于ccd图像处理的视度和视差自动检测系统

所属栏目:工程应用

收稿日期:2011-04-15

修改稿日期:2011-06-08

网络出版日期:--

作者单位    点击查看

张晓明:中国人民解放军92854部队,广东 湛江524005
赵辉:中国人民解放军92854部队,广东 湛江524005

备注:张晓明(1970 -),男,福建晋江人,学士,工程师,主要从事指挥自动化研究。

【1】苏大图,沈海龙.光学测量与像质鉴定[M].北京:北京工业学院出版社,1987.

【2】刘秉琦,周斌.利用CCD实现望远系统视差自动测试的研究[J].半导体光电,2005,26(3):253-255.

【3】张伟,汪岳峰,董伟.光学仪器视差自动检测研究[J].光学技术,2002,28(4):365-366.

【4】CAO Weiguo,XUE Changxi,LI Lijuan,et al.The measurement and system error analysis of diopter and optical parallax in optical pointing system[J].SPIE,2008,6624:1-9.

【5】程守澄.光学仪器检校[M].北京:兵器工业出版社,1992.

【6】曹茂永,孙农亮,郁道银.基于灰度梯度的数字图像评价函数[J].光电工程,2003,30(4):70-72.

【7】王学影,张洪涛.基于图像处理的CCD摄像机自动调焦方法研究[J].测量技术,2005(8):16-18.

【8】宋曙光.图像边缘检测算法研究与分析[J].光机电信息,2010,27(9):44-47.

【9】SUBBARAO M,CHOI T S.Accurate recovery of three dimensional shape from image focus[J].IEEE Transactions on Pattern Analysis and Machine Intelligence,1995,17(3):266-274.

【10】梁翠萍,李清安,乔彦峰,等.简析光学系统自动调焦的方法[J].电光与控制,2006,13(6):93-96.

【11】郑佳,周建忠,何大华.基于视频图像处理的快速对焦方法研究[J].光学与光电技术,2010,8(3):57-60.

引用该论文

ZHANG Xiaoming,ZHAO Hui. A CCD Image Processing Based Automatic Measurement System for Diopter and Optical Parallax[J]. Electronics Optics & Control, 2012, 19(4): 72-75

张晓明,赵辉. A CCD Image Processing Based Automatic Measurement System for Diopter and Optical Parallax[J]. 电光与控制, 2012, 19(4): 72-75

被引情况

【1】牛津,徐熙平,王舒,安志勇. 基于类正弦测微法实现视差的快速定量测试. 光学学报, 2018, 38(4): 412003--1

您的浏览器不支持PDF插件,请使用最新的(Chrome/Fire Fox等)浏览器.或者您还可以点击此处下载该论文PDF