光学 精密工程, 2014, 22 (7): 1857, 网络出版: 2014-09-01   

直圆柔性球铰柔度矩阵的解析计算

Analytical calculation of compliance matrix for right-circular flexure spherical hinge
作者单位
1 燕山大学 河北省并联机器人与机电系统实验室, 河北 秦皇岛 066004
2 燕山大学 先进锻压成形技术与科学教育部重点实验室, 河北 秦皇岛 066004
摘要
基于线弹性和小变形假设理论, 通过引入比例系数(直圆柔性球铰槽口间距与切割半径倍数之比)并利用其结构对称的特点, 推导得到了形式较为简洁的直圆柔性球铰柔度矩阵各子元素的解析柔度计算公式。利用有限元仿真软件验证了所推公式的正确性, 并绘制了相应的误差曲线。结果表明: 当比例系数小于0.2时, 直圆柔性球铰各柔度计算公式的相对误差限均在11%以内; 随着比例系数的增加, 除沿x向的拉压柔度C11误差较小外, 其他柔度计算公式的误差均呈增加的趋势, 最大误差为30%。实验结果显示理论分析与仿真结果基本趋于一致, 验证了直圆柔性球铰各柔度解析式的正确性。本文的研究内容为直圆柔性球铰在实际应用中的结构设计和参数优化奠定了理论基础。
Abstract
On the basis of hypothesis theories of linear elasticity and small deformation, the analytical compliance calculation formula of each sub-element in the compliance matrix of a right-circular flexure spherical hinge was deduced. The formula is succinct in form by introducing the proportional coefficient (The ratio of right-circular flexure spherical hinge groove spacing and double cutting radius) and utilizing the symmetrical feature of the structure. The correctness of the formula was verified by adopting the finite element simulation software, and its error curves were drawn corresponding to the simulated values. The results show that the relative errors of serial compliance calculation formula for the right-circular flexure spherical hinge are within 11% when the proportional coefficient is less than 0.2. With the increase of the proportional coefficient, the errors of the other compliance calculation formulas have a trend of increasing with maximum of 30% except the error of tension and compression compliance C11 along the direction x. The experimental results show that the theoretical analysis is in agreement with the simulation results, which verifies the correctness of the proposed formula. These results will lay a key theoretical basis for the structural design and parametric optimization of the right-circular flexure spherical hinges in practical applications.

姚建涛, 李立建, 杨维, 赵永生. 直圆柔性球铰柔度矩阵的解析计算[J]. 光学 精密工程, 2014, 22(7): 1857. YAO Jian-tao, LI Li-jian, YANG Wei, ZHAO Yong-sheng. Analytical calculation of compliance matrix for right-circular flexure spherical hinge[J]. Optics and Precision Engineering, 2014, 22(7): 1857.

本文已被 2 篇论文引用
被引统计数据来源于中国光学期刊网
引用该论文: TXT   |   EndNote

相关论文

加载中...

关于本站 Cookie 的使用提示

中国光学期刊网使用基于 cookie 的技术来更好地为您提供各项服务,点击此处了解我们的隐私策略。 如您需继续使用本网站,请您授权我们使用本地 cookie 来保存部分信息。
全站搜索
您最值得信赖的光电行业旗舰网络服务平台!