强激光与粒子束, 2014, 26 (11): 112002, 网络出版: 2014-12-08   

SiO2/CH/Au复合黑腔诊断孔电火花加工技术

Fabrication of diagnostic hole of SiO2/CH/Au hohlraum by micro-electrical discharge machining
谢军 1,2,*张昭瑞 1,2梅鲁生 1,2黄燕华 1,2朱磊 1,2刘峰 1,2张海军 1,2李国 1,2宋成伟 1,2
作者单位
1 中国工程物理研究院激光聚变研究中心,四川绵阳621900
2 中国工程物理研究院超精密加工重点实验室,四川绵阳621900
摘要
通过电火花加工技术,采用含碳较高的煤油作为电介质,利用导电性能及加工性能较好的紫铜作电极材料,实现了SiO2/CH/Au复合黑腔侧表面方形诊断孔的精密加工。采用OLYMPUSSTM6测量显微镜对诊断孔尺寸,结果表明:孔的尺寸加工精度可控制在±10μm 内,同一电极加工的诊断孔尺寸一致性可控制在±5μm 内。采用扫描电镜能谱分析SiO2/CH/Au加工导电层的成分,结果表明:电火花加工过程中,由于电介质分解生成游离态的碳以及电极材料铜熔融后沉积在CH 和SiO2层表面,形成辅助导电层。通过加工辅助导电层,产生的瞬时高温使SiO2和CH 层熔融气化,从而实现对绝缘层的加工。
Abstract
The rectangular diagnostic hole on the side of SiO2/CH/Au hohlraum was machined by electrical discharge machining technology, and the dielectric is kerosene which has high carbon content and the electrode material is red copper which has good electrical conductivity. The size of diagnostic hole is characterized by OLYMPUS STM6 measuring microscope. The results indicate that dimension precision of the diagnostic hole is less than 10 μm, and dimension uniformity is less than 5 μm. The components of the conducting layer are characterized by EDS spectrum. The results indicate that carbon, which is product of chemical reaction of kerosene and copper and comes from the electrode, is the key component of the assistant conducting layer.

谢军, 张昭瑞, 梅鲁生, 黄燕华, 朱磊, 刘峰, 张海军, 李国, 宋成伟. SiO2/CH/Au复合黑腔诊断孔电火花加工技术[J]. 强激光与粒子束, 2014, 26(11): 112002. Xie Jun, Zhang Zhaorui, Mei Lusheng, Huang Yanhua, Zhu Lei, Liu Feng, Zhang Haijun, Li Guo, Song Chengwei. Fabrication of diagnostic hole of SiO2/CH/Au hohlraum by micro-electrical discharge machining[J]. High Power Laser and Particle Beams, 2014, 26(11): 112002.

本文已被 2 篇论文引用
被引统计数据来源于中国光学期刊网
引用该论文: TXT   |   EndNote

相关论文

加载中...

关于本站 Cookie 的使用提示

中国光学期刊网使用基于 cookie 的技术来更好地为您提供各项服务,点击此处了解我们的隐私策略。 如您需继续使用本网站,请您授权我们使用本地 cookie 来保存部分信息。
全站搜索
您最值得信赖的光电行业旗舰网络服务平台!