红外与激光工程, 2016, 45 (2): 0206008, 网络出版: 2016-04-05   

激光在高速钢表面加工沟槽表面织构的实验研究

Experimental study on the groove surface texture processed by laser on the surface of high-speed steel
作者单位
1 第二炮兵工程大学装备管理系,陕西 西安 710025
2 中国白城兵器试验中心,吉林 白城 137001
3 中国航天科技集团四院军事代表室,陕西 西安 710025
摘要
沟槽状表面织构广泛应用于机械密封、缸套活塞环等机械摩擦部件,其性能取决于加工后的几何参数,因此高效准确地加工出理想尺寸的织构显得尤为重要。运用不同的激光输出功率、重复频率和扫描速度在高速钢表面加工沟槽状表面织构,设计了三水平三因素的全面实验,系统研究了加工参数与沟槽织构几何参数的关系。结果显示:随着激光重复频率的增加,沟槽织构深度和宽度均呈现先略微增大后减小的趋势。扫描速度增大使沟槽织构深度先增加后减小,而宽度均随着扫描速度的增大而变大。方差分析表明:较之激光输出功率,激光扫描速度、重复频率及其交互作用对织构加工深度和宽度的影响更显著。输出功率在10~14 W之间、重复频率在20~30 kHz之间、扫描速度1 000 mm/s左右时,加工高速钢表面沟槽织构的质量较好。同时,压痕实验证明,在织构边缘区域硬度明显增加。
Abstract
Groove surface texture was widely used in the frictional mechanical part, such as mechanical seal, cylinder liner and piston ring, whose performance depends on its geometric parameter of the texture. Therefore, it is important to process the surface texture efficiently with accurate geometric parameter. Groove surface textures were fabricated on high-speed steel by lasers with different output powers, repetition frequencies and scanning speeds. Comprehensive experiments with three levels and three factors were designed to study the relationships between texture topographies and the three processing parameters. The experimental results showed that the depth and width of the groove surface texture slightly increased firstly and then decreased with the rise of laser repetition frequency. Moreover, with the incensement of laser scanning speed, the depth of the groove surface texture increased firstly and then decreased, but the width of the groove surface texture continued to rise. Variance analysis showed that laser scanning speed and repetition frequency had more obvious influence on the width and depth of groove surface texture thanthe output power. High-quality groove surface texture would be processed on the high-speed steel by laser with the output power of 10W to 14W, the repetition frequency of 20kHz to 30kHz and the scanning speed of about 1000mm/s. Meanwhile, indentation testing indicated that the hardness on marginal area of surface texture markedly increased.

武伟, 陈桂明, 赵娜, 樊博璇. 激光在高速钢表面加工沟槽表面织构的实验研究[J]. 红外与激光工程, 2016, 45(2): 0206008. Wu Wei, Chen Guiming, Zhao Na, Fan Boxuan. Experimental study on the groove surface texture processed by laser on the surface of high-speed steel[J]. Infrared and Laser Engineering, 2016, 45(2): 0206008.

本文已被 3 篇论文引用
被引统计数据来源于中国光学期刊网
引用该论文: TXT   |   EndNote

相关论文

加载中...

关于本站 Cookie 的使用提示

中国光学期刊网使用基于 cookie 的技术来更好地为您提供各项服务,点击此处了解我们的隐私策略。 如您需继续使用本网站,请您授权我们使用本地 cookie 来保存部分信息。
全站搜索
您最值得信赖的光电行业旗舰网络服务平台!