基于响应面分析的T型接头激光深熔焊焊缝形貌预测及工艺参数优化

为了预测激光深熔焊T 型接头的焊缝形貌并优化工艺参数，基于响应面分析的方法，建立了激光深熔焊工艺参数与焊缝形貌特征参数之间的数学模型，进行了方差分析、模型验证。基于所建模型，研究了工艺参数对焊缝形貌的影响规律，并对工艺参数进行了优化，从而实现了对焊缝形貌的预测。结果表明，所建立模型能够准确预测焊缝形貌，预测值与实验值误差很小，经优化的工艺参数既满足焊缝形貌要求也可降低热输入约27％。

Abstract

In order to predict weld profile of T- joints and optimize the process parameters of the laser full penetration welding, the statistical models between parameters and the weld bead geometry of T- joints are established using response surface methodology. Then the analysis of variance is checked and these mathematical models are validated. Based on this model, effects of different process parameters on the weld profile are investigated, the process parameters are optimized, and the weld profile is predicted. The results indicate that the proposed models predict the responses adequately and the predicted values are consistent with experimental results. The optimum welding conditions are found that it can reduce the heat input about 27%.

参考文献

[1] Romanoff J, Remes H, Jutila M, et al.. The stiffness of laser stake welded T-joints in web-core sandwich structures[J]. Thin-Walled Struct 2007, 45(4): 453–462.

[2] Jeffrey D Poirier, Senthil S Vel. Multi-objective optimization of laser-welded steel sandwich panels for static loads using a genetic algorithm[J]. Engineering Structures, 2013, 49: 508-524.

[3] J Jelovica, J Romanoff, S Ehlers. Influence of weld stiffness on buckling strength of laser-welded web-core sandwich plates[J]. Journal of Constructional Steel Research 2012, 77: 12-18.

[4] 胥国祥. 激光+GMAW 复合热源焊焊缝成形的数值模拟[D]. 济南: 山东大学, 2009.

Xu Guoxiang. Numerical Simulation of Weld Formation in Laser+GMAW-Phybrid Welding[D]. Jinan: Shandong University, 2009.

[5] Acherjee B, Misra D, Bose D, et al.. Prediction of weld strength and seam width for laser transmission welding of thermoplastic using response surface methodology[J]. Optics & Laser Technology, 2009, 4(8): 956-967.

[6] Xiao Wang, Cheng Zhang, Kai Wang. Multi-objective optimization of laser transmission joining of thermoplastics[J]. Optics & Laser Technology, 2012, 44(8): 2393-2402.

[7] Bappa Acherjee, Arunanshu S Kuar, Souren Mitra. Experimental investigation on laser transmission welding of PMMA to ABS via response surface modeling[J]. Optics & Laser Technology, 2012, 44(5): 1372–1383.

[8] 姜敏凤, 许贞凯, 刘会霞. 基于响应曲面法的激光透射连接聚合物工艺参数优化[J]. 激光与光电子学进展, 2011, 48(7): 071408.

Jiang Minfeng, Xu Zhenkai, Liu Huixia, et al.. Optimization of laser transmission joining process parameters for thermoplastic using response surface methodology[J]. Laser & Optoelectronics Progress, 2011, 48(7): 071408.

[9] 薛国春, 刘会霞, 李品, 等. 基于响应曲面法的激光透射连接硅与玻璃的工艺研究[J]. 中国激光, 2013, 40(3): 0303004.

Xue Guochun, Liu Huixia, Li Pin, et al.. Process study on laser transmission bonding of silicon with glass via response surface methodology[J]. Chinese J Lasers, 2013, 40(3): 0303004.

[10] U Reisgen. Statistical modeling of laser welding of DP/TRIP steel sheets[J]. Optics & Laser Technology, 2012, 44(1): 92-101.

[11] 卢兵兵. 白车身车顶侧围激光焊接工艺参数分析与优化[J]. 中国激光, 2010, 37(5): 1375-1379.

Lu Bingbing. Analysis and optimization for auto roof to body-side laser welding[J]. Chinese J Lasers, 2010, 37(5): 1375-1379.

[12] Wei Meng, Zhuguo Li, Fenggui Lu. Porosity formation mechanism and its prevention in laser lap weldingfor T-joints[J]. Journal of Materials Processing Technology, 2014, 214(8): 1658-1664.

[13] A Ruggiero. Weld-bead profile and costs optimisation of the CO2 dissimilar laser welding process of low carbon steel and austenitic steel AISI316[J]. Optics & Laser Technology, 2011, 43(1): 82-90.

[14] A G Olabi. Optimizing the CO2 laser welding process for dissimilar materials[J]. Optics and Lasers in Engineering, 2013, 51(7): 832-839.

[15] Benyounis K Y, Olabi A G, Hashmi M S J. Effect of laser-welding parameters on the heat input and weld-bead profile[J]. Journal of Materials Processing Technology, 2005, 164-165: 978-985.

褚振涛, 于治水, 张培磊, 卢庆华, 李绍伟, 马凯. 基于响应面分析的T型接头激光深熔焊焊缝形貌预测及工艺参数优化[J]. 中国激光, 2015, 42(2): 0203006. Chu Zhentao, Yu Zhishui, Zhang Peilei, Lu Qinghua, Li Shaowei, Ma Kai. Weld Profile Prediction and Process Parameters Optimization of T-joints of Laser Full Penetration Welding via Response Surface Methodology[J]. Chinese Journal of Lasers, 2015, 42(2): 0203006.

基于响应面分析的T型接头激光深熔焊焊缝形貌预测及工艺参数优化

关于本站 Cookie 的使用提示

全站搜索

基于响应面分析的T型接头激光深熔焊焊缝形貌预测及工艺参数优化

相关论文

相关资讯

关于本站 Cookie 的使用提示

全站搜索