圆弧金刚石砂轮三维几何形貌的在位检测和误差评价

周炼; 安晨辉; 侯晶; 陈贤华; 王健

doi:doi:10.3788/ope.20172512.3079

光学精密工程, 2017, 25 (12): 3079, 网络出版: 2018-01-10

圆弧金刚石砂轮三维几何形貌的在位检测和误差评价

3D geometric topographic measurement and error evaluation of arc diamond wheel

论文大纲

周炼安晨辉侯晶陈贤华王健

作者单位

中国工程物理研究院激光聚变研究中心，四川绵阳 621900

摘要

针对非球面光学元件加工对圆弧金刚石砂轮形状误差测量的需求，提出了砂轮三维几何形貌在位检测与误差评价方法。建立了砂轮外圆面螺旋扫描轨迹测量数学模型，利用位移传感器获取了砂轮表面轮廓数据；对得到的数据匀滑滤波后沿圆周展开并进行插值处理，得到砂轮三维几何形貌。然后，根据非球面平行磨削加工特点，提出评价圆弧砂轮形状精度的指标。通过提取三维几何形貌轴截面轮廓，进行最小二乘圆弧拟合得到不同相位处的圆弧半径与圆心坐标，并由误差分离获得砂轮表面圆弧的圆度误差、圆周跳动误差及轮廓圆心轴向偏差。最后，对非球面加工圆弧金刚石砂轮进行检测，获得了砂轮的三维几何形貌以及多个关键尺寸及其误差数据：即圆弧金刚石砂轮的平均圆弧半径为55.442 3 mm，半径波动极差为0.16 mm，中央±8 mm环带内圆弧的圆度误差约为5 μm，圆周跳动误差约为2 μm，截面轮廓圆心轴向位置相对偏差为0.008 mm。根据检测结果，进行了大口径复杂非球面磨削实验，得到的元件面形P-V值为4.62 μm，RMS值优于0.7 μm，满足工程的实际需求。

Abstract

For the purpose of detecting 3D geometric topography of an arc diamond wheel precisely and efficiently in aspheric element processing, the methodology of on-machine measurement and the error evaluating of 3D geometric topography were proposed. Firstly, the mathematical model of screw-scanning track for the diamond wheel was established, and the profile data of the diamond wheel were acquired by a displacement sensor. After data filtering and interpolating, the 3D geometric topography of the diamond wheel was established. According to the feature of aspheric parallel grinding, some parameters to criticize the shape accuracy of arc wheel were put forward. By extracting the wheel profile of the axial direction, the arc radius and center coordinates were calculated by least-square circle fitting. And by error segregating, arc error, circular runout error and the deviation of profile center for the diamond wheel were extracted. Finally, an arc diamond wheel in aspheric element processing was measured experimentally. Some key dimensions and errors of the diamond wheel were achieved. The average radius of the wheel is 55.442 3 mm and the fluctuation range of radius is 0.16 mm. The arc error in the girdle of ±8 mm is about 5 μm, the circular runout error is about 2 μm and the relative deviation of profile center is 0.008 mm. By using those measured data, a large scale aspheric optics grinding experiment was performed and results show that the surface errors( P-V and RMS) of the element are about 4.62 μm, and below 0.7 μm, respectively, which satisfies the engineering requirements.

参考文献

[1] 李圣怡, 戴一帆. 大中型光学非球面镜制造与测量新技术［M］. 北京: 国防工业出版社, 2011.

LI SH Y, DAI Y F. New Technology for Manufacturing and Measurement of Large and Middle-Scale Aspheric Surfaces［M］. Beijing: National Defense Industry Press, 2011. (in Chinese)

[2] 殷龙海, 王孝坤, 李龙响, 等. 大口径SiC离轴非球面的高效磨削加工［J］. 光学精密工程, 2015, 23(9): 2497-2505.

YIN L H, WANG X K, LI L X, et al.. Fast grinding of large SiC off-axis aspheric surface［J］. Opt. Precision Eng., 2015, 23(9): 2497-2505. (in Chinese)

[3] GUO Y B, CHEN B K, ZHANG Y, et al.. Research on parallel grinding method of non-axisymmetric aspheric lens［J］. Chinese Journal of Mechanical Engineering, 2004, 17(1): 149-151.

[4] 张宁宁, 王振忠, 潘日, 等. 平行磨削非轴对称非球面光学元件表面形貌［J］. 强激光与粒子束, 2012, 24(6): 1391-1395.

ZHANG N N, WANG ZH ZH, PAN R, et al.. Surface topography of parallel grinding process for nonaxisymmetric aspheric lens［J］. High Power Laser and Particle Beams, 2012, 24(6): 1391-1395. (in Chinese)

[5] 周旭光, 阎秋生, 孔令叶, 等. 砂轮几何参数对非球面轨迹包络磨削的影响研究［J］. 工具技术, 2015, 49(8): 23-26.

ZHOU X G, YAN Q SH, KONG L Y, et al.. Effect of wheel geometry parameters in grinding aspheric with AEGM［J］. Tool Engineering, 2015, 49(8): 23-26. (in Chinese)

[6] 柯晓龙, 林晓辉, 王健, 等. 圆弧砂轮修整评价及非球面磨削误差补偿技术［J］. 强激光与粒子束, 2015, 27(4): 187-191.

KE X L, LIN X H, WANG J, et al.. Evaluation of cup-wheel truing and error compensation in aspheric grinding［J］. High Power Laser and Particle Beams, 2015, 27(4):044102. (in Chinese)

[7] 林晓辉, 马凯威, 黄海滨, 等. 轴对称非球面磨削表面粗糙度和波纹度的分布特性［J］. 强激光与粒子束, 2015, 27(9): 092013.

LIN X H, MA K W, HUANG H B, et al.. Distribution characteristics of surface roughness and waviness error in axisymmetric aspheric grinding［J］. High Power Laser and Particle Beams, 2015, 27(9): 092013. (in Chinese)

[8] MCDONALD A, BAUER R, WARKENTIN A. Design and validation of a grinding wheel optical scanner system to repeatedly measure and characterize wheel surface topography［J］. Measurement, 2016, 93: 541-551.

[9] MCDONALD A, MOHAMED A M O, WARKENTIN A, et al.. Kinematic simulation of the uncut chip thickness and surface finish using a reduced set of 3D grinding wheel measurements［J］. Precision Engineering, 2017, 49: 169-178.

[10] 崔长彩, 余卿, 张遨, 等. 金刚石砂轮表面形貌测量系统［J］. 光学精密工程, 2014, 22(12): 3167-3174.

CUI CH C, YU Q, ZHANG A, et al.. Measurement system of surface topography for diamond grinding wheel［J］. Opt. Precision Eng., 2014, 22(12): 3167-3174. (in Chinese)

[11] 李瑞旭, 崔长彩, 王爽, 等. 基于粒子群优化算法的砂轮三维形貌匹配［J］. 计算机工程与应用, 2016, 52(11): 265-270.

LI R X, CUI CH C, WANG SH, et al.. 3D topography matching of diamond grinding wheel based on particle swarm optimization［J］. Computer Engineering and Applications, 2016, 52(11): 265-270. (in Chinese)

[12] 杜晗, 陈根余, 周聪, 等. 光纤激光在线整形金刚石砂轮检测系统设计［J］. 激光技术, 2016, 40(6): 930-934.

DU H, CHEN G Y, ZHOU C, et al.. Design of detection system of fiber laser online shaping diamond wheel［J］. Laser Technology, 2016, 40(6): 930-934. (in Chinese)

[13] 柯晓龙, 刘建春, 黄海滨. 圆弧金刚石砂轮精密在位检测系统设计［J］. 厦门理工学院学报, 2013, 21(3): 21-25.

KE X L, LIU J CH, HUANG H B. Research on precision on-machine measuring technology for arc diamond wheel［J］. Journal of Xiamen University of Technology, 2013, 21(3): 21-25. (in Chinese)

[14] 李兵, 孙彬, 陈磊, 等. 激光位移传感器在自由曲面测量中的应用［J］. 光学精密工程, 2015, 23(7): 1939-1947.

LI B, SUN B, CHEN L, et al.. Application of laser displacement sensor to free-form surface measurement［J］. Opt. Precision Eng., 2015, 23(7): 1393-1947. (in Chinese)

[15] 毕超, 房建国, 刘京亮, 等. 基于球形目标的激光位移传感器光束方向标定［J］. 光学精密工程, 2015, 23(3): 678-685.

BI CH, FANG J G, LIU J L, et al.. Calibration of beam direction of laser displacement sensor based on spherical target［J］. Opt. Precision Eng., 2015, 23(3): 678-685. (in Chinese)

[16] 彭希锋, 陈爽, 李海星, 等. 几何功能约束最小二乘法双短圆弧检测［J］. 中国测试, 2016, 42(9): 36-40, 45.

PENG X F, CHEN SH, LI H X, et al.. A measuring method for double short circular arcs based on least square fitting met-hod with geometric usage constraint［J］. China Measurement & Test, 2016, 42(9): 36-40, 45. (in Chinese)

[17] 周京博, 李增强, 王亚奇, 等. 微圆弧金刚石刀具刀尖圆弧的测量及评价［J］. 纳米技术与精密工程, 2013, 11(4): 334-340.

ZHOU J B, LI Z Q, WANG Y Q, et al.. Tool tip arc measurement and characterization of micro-arc diamond tools［J］. Nanotechnology and Precision Engineering, 2013, 11(4): 334-340. (in Chinese)

周炼, 安晨辉, 侯晶, 陈贤华, 王健. 圆弧金刚石砂轮三维几何形貌的在位检测和误差评价[J]. 光学精密工程, 2017, 25(12): 3079. ZHOU Lian, AN Chen-hui, HOU Jing, CHEN Xian-hua, WANG Jian. 3D geometric topographic measurement and error evaluation of arc diamond wheel[J]. Optics and Precision Engineering, 2017, 25(12): 3079.

圆弧金刚石砂轮三维几何形貌的在位检测和误差评价

关于本站 Cookie 的使用提示

全站搜索

圆弧金刚石砂轮三维几何形貌的在位检测和误差评价

相关论文

相关资讯

关于本站 Cookie 的使用提示

全站搜索